Join the #1 community for gun owners of the Northwest
We believe the 2nd Amendment is best defended through grass-roots organization, education, and advocacy centered around individual gun owners. It is our mission to encourage, organize, and support these efforts throughout Oregon, Washington, Idaho, Montana, and Wyoming.
This is a like new in box XDM 5.25 9mm competition setup with 5 mags and essential kit that is ready to be use in idpa. Very accurate and already has a match trigger and barrel. 300 rounds through her and is very accurate. Asking $575 cash can entertain some trades. Looking for mk12 parts, good...
Ranger Green medical trauma "blowout" kit. Never used.
Kit is MIL version and contents are still in vacuum sealed resealable bag with an expiration date of May 2022.
D.A.R.K. "Shingle" Trauma Kit Insert
$80 Shipped USPS or meetup near Shoreline, Lynnwood, Edmonds area.
I built my two muzzle loaders about 35 years ago. My first was a percussion lock 50Cal TC Hawken and my second was a flintlock pistol. Those were the days when the kits came rough and required some time to build.
But I had always been fascinated by the Blunderbuss - a hand held flare muzzle...
This is a full size (g17/22) 80% kit with complete lower parts kit.
Takes about 45 mins to complete.
Can answer questions about builds.
$140 shipped no ffl required.
Would trade for 16" flat top upper with f marked fab. Do not need bcg or ch.
+/-$$ as needed.
Thanks
Jason
**slide not...
First gen unit in two tone- This was a Cabelas special run with holster, mag carrier, etc.
Extra back straps not shown but included.
Fired less than 50 rounds. $Withdrawn
Transfers in Whatcom Co. only at this time.
Too many projects and too many duplicates.
No FFL! This is everything you need to complete.
Poly80 full size (g17/22) smooth side 80% kit complete with lpk. Everything you need to complete.
$150
It takes around 45 mins to complete these. Very very simple with a small drill press, a few files...
What is everyone carrying (for pistols) for a BoB or edc cleaning kit? Specifically I'm trying to figure out what the minimum to carry might be. I currently have a boresnake, solvent, oil, and patches in a waterproof, hard sided case.
I need to get a range cleaning kit for my AR10 and that...
In my 30+ years of outdoor/shooting experience I've seen a lot of discussion about types of firearms, ammunition, bug out location, ect but often medical care is skimmed over.
I'd like to start the discussion about "what do you carry medically?" specifically for when you train/go to the range...
New CMMG 22LR Drop-in Conversion Kit. Never used; only opened packaging. Comes with three (3), 25-round, unused CMMG magazines. $150 shipped. PayPal preferred.
Convert your .40 P226 to 9mm with this full upper featuring night sights, barrel, guide rod etc and 1 15 round factory mag. New these are $409 on Sig's website and very hard to find. No FFL required .Yours for only $265 or trade for brass factory 9mm and some .45. No steel cased. Acceptable...
Complete parts kit with original 9mm barrel and horizontal cut receiver ,trunnion included . This one has the side plates and the tube was cut off clean with out damage to the lower section.
No receiver of coarse, so no FFL transfer required.
150.00
Possible trade for factory...
Full upper slide, barrel, guide rod etc for Sig p226 in 9mm with a 15 round magazine. Turn your .40 into a 9mm with this kit. New they retail for $407 and are hard to find. Yours for only $265. No FFL required. I travel I-5 regularly from Salem to Tigard. Call or text Dan at...
As new RCBS Rock Chucker Master Single Stage #09367 Reloading Kit for sale.
The reloading manual is missing, but all other parts are present.
This kit precedes the Rock Chucker "Supreme" Master Kit which included a primer tool.
$235.00 cash, no trades.
Can deliver anywhere in the greater PDX...
Del Ton Rifle kit.
Never used. There might be a few of the lower parts missing. 1 magpul magazine and mbus sights included. Looking for cash only. 200 or best offer. In southwest Portland.At 15 build by unknowncoast posted Nov 17, 2018 at 4:31 PM