Build Thread Portland area (no ship) business that can centric thread AK barrel and engrave SBR info

Messages
125
Reactions
18
looking to SBR 2 rifles soon, I can chop and crown them, but looking to find a place to thread and engrave the 2 rifles. Dont want to deal with shipping and needs to be centric so I can run cans on it.

Thanks
 

Reno

Messages
10,259
Reactions
22,473
Thanks! Yes this will be post fires, but before I file, I want to have my ducks line up. He can thread w/o barrel removal correct?
Uncertain. I’d refer to Tim once available. I’ve known smiths to thread barrels without removing them as well as removing them.
 
Messages
1,504
Reactions
365
You trollin me?
I literally have a CAI imported Romarms SAR-1 that is being threaded by @Velzey and he had to remove the barrel to truly get it done correctly and asked if I want it re-parkerized or custom cerakoted. I went with the latter and just waiting for everything to get back to normal.

It'll be the future host for a Dead Air Wolverine. :)
 
Last edited:
OP
irierider
Messages
125
Reactions
18
I was wondering why it would need a refinish, and to my understanding places with the right machine or speed can do it no issue. Id rather not mess with barrel removal on an AK

Looking back seems i didn't mention gun type ;)

 
If threading is all one needs, the this tool can be used at home. You just need to have the bbl cut, gas port relocated, gas block and fsb relocated and pinned, and all that needs to be in harmony with the stock or Krink gas piston length and location relative to the gas block. Then you’ll need a smaller handguard, trimmed down gas tube and gas tube heat shield. I have some unobtanium parts for making this work nicely.

1EF4A29F-EF5C-4455-A6D9-178E49F8446E.jpeg

My Mini-Me pistol build from 15+ yrs ago
393D9CA0-AA8E-4427-AB04-876B7CCEED52.jpeg
 
Last edited:

Wombat of Doom

Messages
1,856
Reactions
3,641
I was wondering why it would need a refinish, and to my understanding places with the right machine or speed can do it no issue. Id rather not mess with barrel removal on an AK

Looking back seems i didn't mention gun type ;)

I believe ak barrrels frequently need to be refinished due to scratches and such from press fitting. I need to get down to Estacada to get my Draco re barrelled and threaded. (I am planning on 5/8 x 24 I think) The threads on my draco are crazy off and due to barrel length, well, a new barrel will probably just be better.
 

UPCOMING EVENTS

Cerberus Training Group - Skill Builder - Pistol/Rifle Combo
Cerberus Training Group
47 Cattle Dr, Goldendale, WA 98620, USA
Albany Rifle & Pistol Club (ARPC) Gun Show
Linn County Expo Center
3700 Knox Butte Rd E, Albany, OR 97322, USA
Arms Collectors of SW Washington Gun Show
Battleground Community Center
912 E Main St, Battle Ground, WA 98604, USA
DRRC .22 Rimfire Challenge Oct 10
Douglas Ridge Rifle Club
27787 OR-224, Eagle Creek, OR 97022, USA
Oregon State Steel Challenge Championship
Central Oregon Shooting Sports Association
Millican, OR 97701, USA

LATEST RESOURCE REVIEWS

  • J&B Firearm Sales
    5.00 star(s)
    Good local shop
    Picked up a rifle yesterday from J&B. This was the second or third gun purchase over the last few years from them. I always enjoy stopping by...
  • H&K Gun Shop
    5.00 star(s)
    The only place I have found 9mm in stock
    I’ll admit I didn’t even know this place existed, as I don’t tend to go into Forest Grove often. But it’s a giant (looks bigger from the...
  • Revelation Arms
    4.00 star(s)
    Depends who answers the phone
    I was given the number to Roger Loock by Beaver Creek Armory, as I needed parts I had ordered from MCarbo installed on a Kel-Tec Sub2000. On my...
  • Coastal Farm & Ranch - Cornelius
    3.00 star(s)
    Lesson learned
    I’ll take some responsibility here, as I took the employee at their word instead of doing a thorough inspection. Short story is that I asked for a...
  • MK Tactical
    5.00 star(s)
    Good guys!
    I stop in here every once in a while to see what Michael has in the clearance section, and to ask questions when I have a project in mind...
Top Bottom