WTS OR Ruger 10/22 Custom Silhouette, Mosin Nagant PU Sniper

Discussion in 'Rifle Classifieds' started by Flubb, Dec 9, 2018.

  1. Flubb

    Flubb
    Gresham, OR
    Member

    Messages:
    58
    Likes Received:
    48
    Ruger 10/22 in silhouette configuration - $350 plus actual shipping and insurance
    This 10/22 is partially barrel bedded in a Richards Microfit Tac-Driver silhouette stock of custom long length, it's got a Green Mountain 18" .920 bull barrel, EGW extended scope base, Ranch extended steel magazine release, large .22 magnum bolt handle and an overtravel stop in the factory aluminum trigger guard. This rifle is in .22LR despite the large bolt handle. Trigger pull weight is 1.5 pounds.
    Ra7ruGG.jpg XrGt8IS.jpg qSu3SSa.jpg


    SOLD Mosin Nagant PU Sniper - SOLD
    As far as I can tell this is a genuine Tula PU sniper from 1944 (arsenal refinished at some point?). The 91/30 rifle has matching barrel, receiver, bolt, stock and magazine with a bright shiny bore which has not been countermilled at the muzzle. The scope mount is force-matched to the gun and to the scope. The scope has domed screws. No leather scope cap. There is some lacquer flaking on the stock but the steel is in excellent condition.

    If you have any questions or picture requests please let me know, I'll be happy to oblige!
     
    Last edited: Feb 12, 2019
    matts, Flint, fredball and 1 other person like this.
  2. DrCox

    DrCox
    Gresham
    Active Member

    Messages:
    179
    Likes Received:
    63
    PM sent
     
  3. Paul_L

    Paul_L
    Dallas, OR
    New Member

    Messages:
    1
    Likes Received:
    0
    I'm interested in the Mosin, PM on the way.
     
  4. Jbcutter

    Jbcutter
    Hillsboro
    New Member

    Messages:
    11
    Likes Received:
    0
    is the 10/22 available?
     
  5. Flubb

    Flubb
    Gresham, OR
    Member

    Messages:
    58
    Likes Received:
    48
    Yessir, still available!
     
  6. Jbcutter

    Jbcutter
    Hillsboro
    New Member

    Messages:
    11
    Likes Received:
    0
    What's the length of the trigger pull??
     
  7. Flubb

    Flubb
    Gresham, OR
    Member

    Messages:
    58
    Likes Received:
    48
    It's about 1mm or maybe 3/64". Here it is at a resting state. There's a little takeup before the wall so it's less than the gap in this image. I thought the trigger was completely factory other than the overtravel stop I installed, but the pull weight is a consistent 1.5 pounds so clearly I replaced some springs at some point. The hammer and sear look like Ruger factory, not VQ or some other.

    HYolO31.jpg
     
    Last edited: Dec 12, 2018
  8. Jbcutter

    Jbcutter
    Hillsboro
    New Member

    Messages:
    11
    Likes Received:
    0
     
  9. Jbcutter

    Jbcutter
    Hillsboro
    New Member

    Messages:
    11
    Likes Received:
    0
    Measuring from the trigger to the butt stock
     
  10. Flubb

    Flubb
    Gresham, OR
    Member

    Messages:
    58
    Likes Received:
    48
    I feel silly.

    The length of pull is 14".
     
    x2ndxall likes this.
  11. Jbcutter

    Jbcutter
    Hillsboro
    New Member

    Messages:
    11
    Likes Received:
    0
    I will be out near the airport Saturday morning I'm interested for sure Have a union meeting at 10:00am
     
  12. Flubb

    Flubb
    Gresham, OR
    Member

    Messages:
    58
    Likes Received:
    48
    I wanted to get some groups on paper to go with this gun. Unfortunately the table I was on was rickety so I was shaking all over and I forgot my rest and bags at home so I had to lay the rifle over my range bag for support. But even with all these lame excuses some of these groups are under 1 MOA!

    On a stable bench, with a good shooter, and even with decent quality non-match ammo this gun is definitely under 1 MOA.


    IMG_3339.jpg
     
    matts likes this.

Share This Page