Join the #1 community for gun owners of the Northwest
We believe the 2nd Amendment is best defended through grass-roots organization, education, and advocacy centered around individual gun owners. It is our mission to encourage, organize, and support these efforts throughout Oregon, Washington, Idaho, Montana, and Wyoming.
Discuss firearms and all aspects of firearm ownership
Join others in organizing against anti-gun legislation
Find nearby gun shops, ranges, training, and other resources
Discover free outdoor shooting areas
Stay up to date on firearm-related events
Share photos and video with other members
...and much more!
wbp
In materials, BS 1088 is the British Standard specification for marine plywood that applies to plywood produced with untreated tropical hardwood veneers that have a set level of resistance to fungal attack. The plies are bonded with Weather Boil Proof (WBP) glue.Although this is a British Standard, the finished product does not have to be made in Britain, just manufactured to meet the standard. The standard is associated with Lloyd's Register since it performs testing of products to this standard. It does not follow that it is a structural plywood.
WBP Glue Line -- BS 1088 plywood must use an adhesive, which has been proven to be highly resistant to weather, micro-organisms, cold and boiling water, steam and dry heat. The product's bonding must pass a series of British Standard tests.
Face Veneers -- These must present a solid surface that is free from open defects. Face veneers must be free of knots other than "sound pin" knots, of which there shall be no more than six(6) in any area of one(1) square foot, and there can be no more than an Average of two(2) such knots per square foot area over the entire surface of the plywood sheet. The veneers must be reasonably free from irregular grain. The use of edge joints is limited, and end joints are not allowed.
Core Veneers -- Core veneers have the same basic requirements as face veneers, except that small splits are allowed, and there is no limit on the number of pin knots or edge joints. However, end joints are not permitted.
Limits of Manufacturing Defects -- Defective bonds, pleats and overlaps, and gaps in faces are not permitted. Occasional gaps may be repaired using veneer inserts bonded with the proper adhesive.
Moisture Content -- BS 1088 plywood must have a moisture content between 6% and 14% when it leaves the factory.
Finishing -- Boards will be sanded on both sides equally.
Length & Width -- The length or width of a board produced as a standard size shall not be less than the specified size nor more than 6.3 mm (0.25") greater than the specified size.
Squareness -- The lengths of the diagonals of a board shall not differ by more than 0.25% of the length of the diagonal.
Thickness Tolerances -- Tolerances vary as follows.
4 mm +.02/-0.6 ; 6 mm +.04/-0.65 ; 9 mm +.06/-0.75 ; 12 mm +.09/-0.82
15 mm +.1/-0.9 ; 18 mm +.12/-0.98 ; 22 mm +.16/-1.08 ; 25 mm +1.8/-1.16From the above we can assume that 6 mm material will arrive at thickness' between 6.04 mm and 5.35 mm.
Face Veneer thickness -- For any three-ply construction, which applies to 3 and 4 mm material, each face veneer shall be not thinner than 1/8 of the total thickness of veneers assembled dry. Since the dry thicknesses of the boards are 3.6 and 4.6 respectively, we can assume that, for these thicknesses only, the face veneers will be as follows:
3.6 mm dry x 12.5% (1/8) = 0.45 mm 4.6 mm dry x 12.5% (1/8) = 0.575 mmMulti-Ply Construction-- This applies to boards thicker than 4.8 mm (3/16")
Each face veneer shall be a minimum of 1.3 mm and not thicker than 3.8 mm.
Each core veneer shall be no thicker than 4.8 mm
Selling my AK47 WBP Mini Jack Pistol(model# SR762C)
This thing is a riot to shoot. Spits fireballs and sounds like a cannon. I have probably 250 rounds through it and it has been flawless, just need to make room for other toys.
I'll include one steel magazine and one bakelite too.
Looking...
Hey everyone, I’m selling my WBP Fox ak47. The gun is brand new never fired. It also comes with two magazines. If you have any questions please ask here or PM me! I’ve set the price very fair hoping for a quick sale.
First person available to meet will get first opportunity to purchase...
polish builds are too of the line. Their barrels are best out I think. Review are good. This brand new never sh*t cones with brand new 30rd mag in the box asking $1200 please PM or text only at 509-251-5325
Manufactured by WBP Rogow Poland
FB Radom Hammer Forged Chrome Lined 10 inch Barrel...
Like new WBP FOX AK for SALE
Shot around 200 rounds through it - like new
Mods included:
ALG Trigger
Krebs Safety
Polish Bakelite Grip
Vickers Sling
RS Regulate Mount 302
Primary Arms SLX Optic
Comes with the orginal box, grip, and safety.
Looking for $1650 and transfers at Brads Guns...
Hi all. Up for sale is a wbp fox ak-47 made in Poland by WBP Rogow. Purchased from Atlantic Firearms last year. Fired three rounds to sight it in and it has sat in my safe since. It will come with original box, magazine and polish surplus sling. Could add ammo for a little additional $. Not...
Bought this Polish kit from What a Country, but decided to go a different direction. These should fit on pretty much any AKs with a standard rear trunnion (but verify before you buy).
Includes:
Folding stock with two screws
Black poly handguards
Black poly pistol grip (no screw included)