glock compatible 80% receiver

[oli700]

Pretty simple for me - 80% lower, no registration, no serial number. If nothing else, it's a middle finger to the grimy gun grabbers. That said, if I get worried about metal rails, I'll take a look at those 80% 1911 lowers, like the one Bolus built.

thats why I like it, lots of folks pay over going rate to do that in AR.....I'm about to join them

 

[RicInOR]

What are the stresses in the lower?

If you can 3d print most of it - then why not just 3d print a dozen. Get to some round count and change?

If you are thinking well I need one for use in North Dakota in February with a 70 ton tank likely to run over the pistol ... then good luck with that.


Slo-Mo showing polymer frame will flex a lot when shot and those are the forces which will break your frame. The pressure is contained in the chamber. How much stress at the back of the frame when the slide comes back?

10mm really?


How about 380? A gun without a serial number is so you have something.

 

[PBinWA]

Looks like they have some form of metal insert that reinforces the rails. Got to watch the video on their site.

 

[etrain16]

What are the stresses in the lower?

If you can 3d print most of it - then why not just 3d print a dozen. Get to some round count and change?

If you are thinking well I need one for use in North Dakota in February with a 70 ton tank likely to run over the pistol ... then good luck with that.


Slo-Mo showing polymer frame will flex a lot when shot and those are the forces which will break your frame. The pressure is contained in the chamber. How much stress at the back of the frame when the slide comes back?

10mm really?


How about 380? A gun without a serial number is so you have something.

Interesting video, I was not aware how much a polymer frame can flex while shooting. But one thing stands out for me in the video is the gun isn't being held very tight - you can see it fail to go into battery, twice, like it's being limp-wristed. It does make me wonder if it would flex as much if the 'grip' were a bit stronger, like a shooter would hold it.

 

[Flopsweat]

Interesting video, I was not aware how much a polymer frame can flex while shooting. But one thing stands out for me in the video is the gun isn't being held very tight - you can see it fail to go into battery, twice, like it's being limp-wristed. It does make me wonder if it would flex as much if the 'grip' were a bit stronger, like a shooter would hold it.

Or would it flex even more?

 

[oli700]

the flex is the beauty of the Glock frame

its a major contributor to why they harness the hot 10mm better than a steel frame,perceived recoil feels better, less of a sting transmitted to the hands, more of a hard push than the snappy sting

I prefer steel frame handguns.....but 10mm in poly

 

[bolus]

Anyone else getting one? Im starting to look for G17 parts as I hope this kit to ship in the next few weeks

Anyone have a good source for parts?

I see complete slide assemblies for in the G17 in the $340 range
http://www.glockmeister.com/GLOCK-17-Complete-Upper/productinfo/G17UPPER/
http://www.omahaoutdoors.com/glock-accessories-parts/glk-g17-g3-upper/

ebay ones are low $300 used, high $300 new

Receiver parts kits are $75 (it needs a 3 pin lower parts kit)
http://www.glockmeister.com/Complet...rts-Kit-For-3-Pin-G17/productinfo/G17RECKIT3/

http://www.rockyourglock.com/custom/G17RECKITGEN3.htm

anywhere else that would be good to look?

 

[etrain16]

Anyone else getting one? Im starting to look for G17 parts as I hope this kit to ship in the next few weeks

Anyone have a good source for parts?

I see complete slide assemblies for in the G17 in the $340 range
http://www.glockmeister.com/GLOCK-17-Complete-Upper/productinfo/G17UPPER/
http://www.omahaoutdoors.com/glock-accessories-parts/glk-g17-g3-upper/

ebay ones are low $300 used, high $300 new

Receiver parts kits are $75 (it needs a 3 pin lower parts kit)
http://www.glockmeister.com/Complet...rts-Kit-For-3-Pin-G17/productinfo/G17RECKIT3/

http://www.rockyourglock.com/custom/G17RECKITGEN3.htm

anywhere else that would be good to louck?

For slides, I've bought several on Ebay as that's been the best price I could find, usually on a used slide. I've only bought one receiver parts kit and that was also on Ebay, about the same price you show above.

You could also do what I did - buy a used G22 slide and add a conversion barrel - I got both for just under $350, and I can shoot 2 calibers. Here is a used G22 slide for $249: http://www.ebay.com/itm/Glock-22-40...622990?hash=item542916f40e:g:gckAAOSwa-dWlGYe

As for the 80% kit, I do want one, just not in the budget at the moment. And, I'd really like to see the results from someone else before I dive in. I'll be watching for your report.

 

[bolus]

got the update today they are tweaking the frame so it wont ship until March 1st.

 

[etrain16]

got the update today they are tweaking the frame so it wont ship until March 1st.

I suppose it's better they delay it and get it right rather than let their customers find the flaws for them.

 

[bolus]

I suppose it's better they delay it and get it right rather than let their customers find the flaws for them.

Definitely want them to make it right and test it out

"We promised you an update on the Spectre project this week, and so we shall deliver. Here is where we stand in the respect to both the "Spectre" Jig and Frame manufacturing process:

Jig Production Update: The injection mold for the Jig System is complete. Production will start on Tuesday 19th or Wed 20th

Pistol Frame Update:
The injection mold was utilized late December to produce our first set of samples. The frame has been used to test fire rounds and the mold is working. On the other hand, from that sampling we've determined several critical items that need correction. Some are cosmetic, but others are more functional to ensure longevity and strength of the product.

• The grip has a pattern we call Hexigrip, which is being raised slightly higher than the original design, as well as centered better on the overall grip design.
• The picatinny rail system is being tweaked to the milspec.
• The windage is being modified and tested on the mold to allow the product to cure to the proper specifications.
• Screw holes for the custom locking block are being designed/added to the frame.
• The metal locking block is being modified in a few key areas along the rail system to allow for better insertion into the CNC machine for finish work. The locking block is simultaneously the front rail and locking block integrated together.

These key modifications will require an additional 30 days to complete and then re-test. Our goal is to begin shipping by March 1st. As many of you know, Polymer80 will always deliver. We want the best product possible for our customers so as a result, we will ask for your patience as we work through these modifications which will give you one of the best and most unique pistol frames on the market.

We will be updating our website as things progress. We will also be releasing a test shooting video before the product release date."

 

[rdb241]

Got the very same e-mail also. Good to know where my order is.

 

[bolus]

shown at shot shot. gives a brief overview of the finishing steps. it says "1911 grip" I wonder what that means for mags.

 

[bolus]

Here is something different for this project
22tcm conversion for glock 17. looks like it comes with all the parts to fit this frame. so this adds an option for an 80% 22 tcm firearm
https://advancedtactical.com/products/top-sellers/22tcm9r-conversion-for-glock-17-22

 

[bolus]

shipping date moved to the first part of April. Looks like my order number is in the batch to me mailed on the first day.

lower parts kit specifically for the Spectre (on back order)
http://glockparts.com/Detail.aspx?PROD=126735&CAT=809

Draft of install instructions
http://www.polymer80.com/assets/images/Documents/Instructions/S150Instruction.pdf

 

[bolus]

Finished pics starting to show up

 

[ZA_Survivalist]

Finished pics starting to show up

View attachment 283134

What was the total cost in the end? Cheaper than a factory glock?

 

[Stomper]

Now THAT looks like a Lego gun.

 

[bolus]

What was the total cost in the end? Cheaper than a factory glock?

$136 for frame, $65 for lower parts and $340 for complete slide. So more than a retail glock 17.

 

[ZA_Survivalist]

$136 for frame, $65 for lower parts and $340 for complete slide. So more than a retail glock 17.

But still very cool