Quantcast
  1. Sign up now and join over 35,000 northwest gun owners. It's quick, easy, and 100% free!

Feed Problem With my New CZ.. Can you help?

Discussion in 'Handgun Discussion' started by glockguy, May 27, 2009.

  1. glockguy

    glockguy Albany Oregon Well-Known Member

    Messages:
    1,876
    Likes Received:
    60
    Soo I am having a slight problem with my new CZ Rami 2075 .40... Now When I load a clip into it.. and Cock it.. It will shoot the round, and it may shoot the next few.. but almost every time at least once once per clip i shoot.. When I fire off a shot and it injects another round in... the tip of the bullet will hit the bottom of the barrel and the slide will hit the back of the shell causing the bullet to jam the slide open...My Barrel Is also quite loose when the slide is back, but yet everything's in place.. this gun isnt a very good Defense gun :bluelaugh: any thought on how to fix this?
     
  2. Frog

    Frog Vancouver, Washington Member

    Messages:
    612
    Likes Received:
    9
    I'm no expert Glockguy, but from what I've 'picked-up' here, I'd suggest 3 things.
    1. Fire a couple of hundred rounds through it to break it in, using some real good ammo.

    2. Then try different ammo and see what works best.

    3. Keep the gun clean, and don't use to much oil.

    Hope this helps, and others can help if the problem stays consistant.

    Frog.
     
  3. glockguy

    glockguy Albany Oregon Well-Known Member

    Messages:
    1,876
    Likes Received:
    60
    Iv Put about 300 Through it.. and Iv tried 3 different type and brands of ammo... But being there's a SHORTAGE of ammo.. Experimenting is down to a min.
     
  4. Frog

    Frog Vancouver, Washington Member

    Messages:
    612
    Likes Received:
    9
    Understand, and was thinking the same thing when I Replied.

    I'd consult the manufacture for an opinion.

    Frog.
     
  5. Keane

    Keane Hillsboro, OR Active Member

    Messages:
    734
    Likes Received:
    52
    Check out this: http://www.sightm1911.com/lib/tech/FTF_FTE.htm
    It is for a 1911, but it has a few things that look like they could fit.

    It seems to me that the Magazine is presenting the round improperly, or the feed ramp is too rough/oddly shaped. It might be worth giving it a bit of a polish.
     
  6. toys

    toys PDX Member

    Messages:
    116
    Likes Received:
    0
    before you do any modding i would try.

    1. a different mag.
    2. different ammo.
    3. if it still is a problem, i would call CZ and let them know what ammo youve shot and what the problem is. CZ has great CS
     
  7. Keane

    Keane Hillsboro, OR Active Member

    Messages:
    734
    Likes Received:
    52
    qft.
     
  8. Spad

    Spad Kennewick,WA, the desert side Active Member

    Messages:
    439
    Likes Received:
    28
    I had a CZ Rami 9mm with a stainless slide. Had problems like you. CZ has an internet contact on thier USA website. I e-mailed them and they called me in a few days, I explained the problem, they had the pistol picked up (gave me instructions&paid the shipping)). Week or so later they called and said that run of Rami's had problems and offered me another Rami new or a CZ PO-1. I opted for the PO-1 for personal reasons. It has been a real fine pistol. I consider CZ service to be excellent all at no cost to me.I would call them or e-mail them. The service was fast. Bill
     
  9. actionflies

    actionflies Beaverton, Oregon Member

    Messages:
    133
    Likes Received:
    12
    The RAMI in 40 S&W is a known problem for feeding issues from CZ forums. You should call CZ first and if they can't help then you need to buy wolff magazine springs which are stronger. Somehow RAMI in 9mm is not a problem.