Platinum Lifetime
- Messages
- 645
- Reactions
- 428
Moving to a new thread with a better title.
Cleaning up a little... I don't plan on using these, so I'm hoping someone else might. Not necessarily listed in any order...
Cleaning up a little... I don't plan on using these, so I'm hoping someone else might. Not necessarily listed in any order...
- Precision Reflex PRI 05-070-07 Forearm Sling Swivel Rail - $20 SOLD
- Mounts to the Gen III CF handguards, has a QD sling cup, a standard sling post, and includes a QD sling loop
- Used on my MK12-ish build before I decided to make it closer to a MK12 Mod H and needed a longer bottom rail
- Aero Precision Ultralight 30mm Extended Scope Mount - $50 SOLD
- Test fit only to realize I needed a super-extended for the build I was doing
- Ballistic Advantage Modern Series 300 BLK barrel - $120 SOLD
- 1:7 twist, 5R Rifling
- Used - less than 100 rounds down the pipe
- Includes no-name steel gas block and stainless pistol-length gas tube
- BCM Gunfighter Grip Mod 3 (w/ screw) - $15 or trade for black SOLD
- Wolf Grey
- More vertical angle like Magpul K2
- Test fit, never fired with
- Great grip - most of my ARs have one of these except one... Because this color grey was too light compared to the other grey parts I had on it!
- Aero Precision M4E1 Enhanced upper receiver - $100 GONE
- Assembled with dust cover and forward assist
- Made for use with BAR diameter handguards made by many brands (including Aero)
- Includes barrel nut wrench
- Used - less then 100 rounds fired with this upper
- Aero Precision Quantum 9" Keymod Handguard - $40
- Works with the BAR barrel nut or with the M4E1 Enhanced Upper
- Includes short rail section at 12-o-clock at front
- Mounting screws included
- Suppressor diameter if used with very short barrels
- Stops just behind the muzzle device on the above 300 BLK barrel
- Used - less than 100 rounds fired with this handguard
- Generic Charging Handle - $10
- Not much to say...pretty much like every other basic charging handle
- New, other than test fit and racked a few times.
- PSA Nitride Bolt Carrier Group - $50 SOLD
- Nitride coated bolt carrier
- Carpenter 158 steel bolt
- No logos or markings on the carrier
- New - never fired
- Ruger AR grip (w/ screw) - $5 (or FREE with purchase)
- Standard angle (25?)
- Came on my Gen1 Precision Rifle, fits any AR
- Used maybe 20 rounds... If that matters
- Sig MCX Virtus 15" "Low Profile" Handguard Black - $140
- Brand new
- Came with a Virtus AR conversion kit I bought, but I don't need this handguard
- Stops exactly behind the muzzle device on a 16" MCX barrel
- Sig MPX Faux Suppressor - $20
- Threaded M13.5x1LH with hex flats
- Came with my MPX Tacops, but that now has a real can on it...
- Fits on a 4.5" barrel (K models) and will extend out past the end of the 8" handguard
- Has seen about 100 rounds through it
- Sig MPX/MCX Collapsing Pistol Brace - $140
- Mounts to rail on back of receiver
- NOT compatible with the MCX AR conversion (can only be used on a real MCX or MPX lower)
- Official Sig-branded brace - it's got a sling loop on the bottom of the rail mount that is not on the SB Tactical ones
- Used - about 100 rounds through the host before I pulled it off
- Strike Industries Viper PDW Stock - $200
- Spring loaded open, two position stock (open/closed)
- Surprisingly decent cheek rest if you use the rubber extension piece
- Comes with proprietary buffer tube, buffer, spring
- Had the same ~100 rounds through it as the upper and barrel above - ran flawlessly
- Know your laws - this is not a brace
Last Edited: