Colt MK IV 70 Series 1911 Govenment Customized 45 Auto. "Don't Make Me Keep Her"

Discussion in 'Handgun Classifieds' started by arjunki, Oct 17, 2009.

Thread Status:
Not open for further replies.
  1. arjunki

    arjunki
    Beaverton
    Active Member

    Messages:
    819
    Likes Received:
    43
    "SOLD!" I say don't make me keep her because I used to be really into 1911's and I'd rather not get back into the addiction. This is a nice one too. I just took it in on trade from a guy that didn't shoot it a whole lot maybe 500 rnds. The gun has a bit of holster wear on it but as the photos show the usual wear areas are very minimal and the guy had it sent off for a couple grand worth of custom work.
    Here's a breakdown of what was done to it.

    -dehorn

    -rounded butt of pistol. Soooo much nicer to shoot without that butt digging into your hand or your gut when carrying it.
    Polished & throated.

    -had EGW mill the slide for Heinie sights. Has Heinie sight cuts, but the rear is a Yost Professional, no tritium. Front is a Heinie with tritium.

    -Yost Professional bar stock trigger group, consisting of hammer disconnector and sear.

    -EGW firing pin stop, slightly beveled

    -STI thumb safety, just like on the Dan Wesson's. The guy had a CBOB and liked this safety so much he put on on this Colt. Went through a Wilson and an Ed brown before settling on this one. Not too wide but not too narrow. Just right!!

    -beveled magwell

    -Norrells Moly Resin Flat Black finish. Has held up very well for the amount of carrying it's seen. Slight holster wear at muzzle. . Norrells says you can spray wear spots to touch it up, so no need to do entire pistol again. But I personally wouldnt even worry about the minor wear.

    -Wilson barrel bushing.

    -Don't know the maker of the stocks, but they are nice looking. Grippy, but not so much it hurts.

    - Wilson beavertail

    -Wolff sear spring

    -Ed brown 30lpi mainspring housing

    -Ed brown extended mag release

    Cash price is $800.00 FTF in Oregon
    I would consider trades for up to 1/2 value + 1/2 cash
    "Just PM and ask"
     
  2. rltrim46ford

    rltrim46ford
    lebanon
    Well-Known Member

    Messages:
    1,169
    Likes Received:
    336
    Send me your email and I will send you some pics of a Sig 220 in 45 ACP with box and I think 4 mags and Hogue grips.

    Louie
     
  3. arjunki

    arjunki
    Beaverton
    Active Member

    Messages:
    819
    Likes Received:
    43
    Back up for sale!
     
  4. arjunki

    arjunki
    Beaverton
    Active Member

    Messages:
    819
    Likes Received:
    43
    Who has a new generation Glock 27, 33 or even a 26 in new or like new condition! I would make you a screamin deal if you do!:thumbup:
     
  5. Just Jim

    Just Jim Well-Known Member

    Messages:
    6,828
    Likes Received:
    6,281
    My wife would kill me if I traded off her 26 lol

    jj
     
  6. skud_dusty

    skud_dusty
    Salem, OR
    Active Member

    Messages:
    752
    Likes Received:
    120
    Who did the work?
     
  7. ajzway

    ajzway
    Coos Bay, OR
    Member

    Messages:
    59
    Likes Received:
    0
    I have a 3rd generation, LNIB Glock 27, two 9 round mags with grip extensions, 4 months old, I bought new. Only 200 rounds through it. Not a mark on it. This is my wifes gun, but I let her shoot my 1911 and now she wants one also. I am interested in your screamin deal.
     
  8. arjunki

    arjunki
    Beaverton
    Active Member

    Messages:
    819
    Likes Received:
    43
    STG (Scattergun Tech Group) did most if not all of the work.
     
  9. Grubstake

    Grubstake
    Eugene Oregon
    Member

    Messages:
    136
    Likes Received:
    1
    PM Sent
     
  10. arjunki

    arjunki
    Beaverton
    Active Member

    Messages:
    819
    Likes Received:
    43
    Sold
     
Thread Status:
Not open for further replies.

Share This Page