Join the #1 community for gun owners of the Northwest
We believe the 2nd Amendment is best defended through grass-roots organization, education, and advocacy centered around individual gun owners. It is our mission to encourage, organize, and support these efforts throughout Oregon, Washington, Idaho, Montana, and Wyoming.
Discuss firearms and all aspects of firearm ownership
Join others in organizing against anti-gun legislation
Find nearby gun shops, ranges, training, and other resources
Discover free outdoor shooting areas
Stay up to date on firearm-related events
Share photos and video with other members
...and much more!
7.3l diesel
The LS based small-block engine is the primary V-8 used in General Motors' line of rear-wheel-drive cars and trucks. Introduced in January 1995, it is a "clean sheet" design with only rod bearings, lifters, and bore spacing in common with the longstanding Chevrolet small-block V-8 that preceded it as the basis for GM small-block V-8s. The basic LS variations use cast iron blocks, while performance editions are all aluminum with cast iron cylinder liners. The engine block and cylinder heads are cast at Saginaw Metal Casting Operations in Saginaw, Michigan.
The LS small-block has been manufactured in three Generations – III, IV, and V – with preceding Generations I and II of modular GM small-block engines having been based on the Chevrolet small-block V-8 originally released in 1954. GM recycled the "LT" designation beginning with the LS Generation V "LT1" in 2014.
Several versions of the LS were used in the Chevrolet Corvette, beginning with the LS1 in 1997 through the LS9 and others in 2013. Variants of the LT version of the GM small-block have been used since.
Most of the credit for this engine family must go to Ed Koerner, GM's Powertrain vice president of engineering operations at the time. He was a V-8 design veteran and former National Hot Rod Association (NHRA) record holder in drag racing. Koerner had been the Chief Engineer for all the existing GM small-block V-8 engines and was put in charge of the "all-new" Gen III LS1 V-8 development project, which would share no parts with previous engines. Design team members included Alan Hayman, Jim Mazzola, Ron Sperry, Bill Compton, Brian Kaminski, Jon Lewis, Stan Turek, Don Weiderhold, and Dave Wandel.
The performance improvements in the LS-family V-8s over the previous classic small-block V-8 family are several. The lower section of the block incorporates deep side skirts, along with 6-bolt cross-bolted main bearing caps. This fully boxes the crankshaft, creating a very strong and rigid structure that has been hot-rodded by enthusiasts to over 1,000-HP.
Although it is the same compact physical size as the classic small-block V-8, this block can accept a 4-inch stroke as an option in its stock form, due to the cam location being elevated slightly, compared to previous block designs. Also, the cam bearing journals are larger, to allow for a higher cam-lift profile than was previously possible. The stock aluminum heads can provide a high amount of air-flow, which previously could only be found in aftermarket race-performance heads.
The aluminum heads also incorporate steam vents to prevent gas pockets from building up in critical areas, and this is vital in allowing the coolant to manage heat build-up for high-performance applications. Such design features allow for a higher compression ratio with no fear of detonation. The thermostat has been located at a low position, which eliminates the possibility of a gas pocket preventing the thermostat from properly sensing the heat of the coolant.
Previous generations incorporated a coolant passage through the intake manifold to warm the incoming fuel-air mixture in very cold climates. However, modern fuel-injection techniques eliminate fuel atomization concerns under all conditions, so the LS family uses a dry intake manifold. This removes a common coolant leakage point and also allows the incoming air to remain as cool as possible for better power production.
I have a nice but older diesel pickup, no integrated chip on the key. I need to get off my butt and put in a kill switch to mitigate the risk of theft.
I did a bit of research and assume I'll probably want a solid, 30-amp switch.
Anyone done it before? Thoughts, or things you'd do...
My father-in-law bought this new and I bought it from him. It’s in great shape! Has been regularly serviced by the same mechanic since it was new. Just had the starter and fly wheel replaced. Only 171,xxx miles, so a ton of life left.