*SOLD* VLTOR imod mil spec stock 50$ or trade for AR stuff

Discussion in 'Part & Accessory Classifieds' started by gonzo1082, Sep 10, 2011.

Thread Status:
Not open for further replies.
  1. gonzo1082

    gonzo1082
    Damascus, OR
    Member

    Messages:
    237
    Likes Received:
    9
    like new, no blemishes. does not fit on my new bushmaster commercial buffer tube



    looking for:

    quad rail handguard
    comparable commerical stock (magpul moe)
    magpul afg2
    cheap red dot with quick release

    NOT looking for:
    ammo
    chickens
    ducks

    vltor1.jpg

    vltor2.jpg

    vltor3.jpg
     
    Last edited: Sep 10, 2011
  2. The B

    The B
    NW Oregon
    Well-Known Member

    Messages:
    3,997
    Likes Received:
    2,601
    lame.. all i have is ducks
     
  3. gonzo1082

    gonzo1082
    Damascus, OR
    Member

    Messages:
    237
    Likes Received:
    9
    yeah. last time I took ducks as payment they were defective.

    (no self bump intended)

    Sent from my Nexus S 4G using Tapatalk
     
  4. FA9

    FA9
    Hillsburrito, ORgun
    Well-Known Member

    Messages:
    806
    Likes Received:
    436
    Lol Great ad. Anyway, I'm new to the ar world. Could you just replace the buffer tube so that you could use the stock? It's just the buffer that's different right?
     
  5. SVT-ROY

    SVT-ROY
    Tigard
    Resident Beretta guru

    Messages:
    860
    Likes Received:
    182
    Pm sent
     
  6. gonzo1082

    gonzo1082
    Damascus, OR
    Member

    Messages:
    237
    Likes Received:
    9
    pm replied

    I'm new to ARs too. from what I read I'd have to replace the buffer tube but there would be tiny wiggle since the lower was for for the commerical buffer tube.

    Sent from my Nexus S 4G using Tapatalk
     
  7. FatherHolyHoly

    FatherHolyHoly
    MN
    Active Member

    Messages:
    584
    Likes Received:
    127
    FYI. The wiggle comes when you put a commercial stock on a milspec tube.
    The receiver will take either tube.
    That said, cheapest milspec tube I found was around $28 shipped, new.
    (unless you go with UTG. They were even cheaper, but I don't care for their stuff)
     
    gonzo1082 and (deleted member) like this.
  8. Stomper

    Stomper
    SCREW YOU SALEM!!
    SCREW YOU SALEM! Gold Supporter

    Messages:
    17,868
    Likes Received:
    40,730
    It's a good thing you won't take any ducks for trade... quak kills!!
     
  9. skydiver

    skydiver
    Sandy,OR
    Well-Known Member

    Messages:
    645
    Likes Received:
    412
    Go Beavs! :)
     
  10. gonzo1082

    gonzo1082
    Damascus, OR
    Member

    Messages:
    237
    Likes Received:
    9
    LOL to all comedic replies.

    trade pending :)
     
  11. The B

    The B
    NW Oregon
    Well-Known Member

    Messages:
    3,997
    Likes Received:
    2,601
    the threads are identical for milspec and commercial receiver extensions (buffer tubes)... there's no difference with receivers.
     
    gonzo1082 and (deleted member) like this.
Thread Status:
Not open for further replies.

Share This Page