- Messages
- 872
- Reactions
- 1,400
- Ad Type
- For Sale
- Price
- $40
- Manufacturer
- Other / Not Listed
- City
- Tigard
- State
- Oregon
- Zip Code
- 97223
*Sold Pending Funds*
Like New - this is great (M-LOK) equipment!
Hand Stop:
"The Arisaka Defense Hand Stop is a continuation of low profile, minimal control accessories. The primary goal of this accessory is to aid the user in pulling their rifle into their shoulder, enhancing control and recoil mitigation. The Hand Stop can also be used as a barricade stop, or reversed and placed at the front of the handguard to prevent the support hand from slipping off the end. The size and profile were designed to fit a wide variety of hands without being too large to get in the way. The Hand Stop is CNC machined from 6061-T6 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP20/T20 Torx wrench for installation (not included).
Height: 1.3"
Width: 0.625" at widest point.
Length: 1.4"."
Indexer:
"The Arisaka Defense Indexer is a continuation of the low profile, minimal control accessories Arisaka is known for. It was developed due to end-user demand for an M-Lok version of the Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. The Indexer can be used in a variety of ways, but the main intent is to place it between two fingers (usually index and middle). This typically places it further forward on the handguard, which also means it doesn't get in the way when transitioning to kneeling or prone shooting positions, where most people move their support hand towards the rear. Used in this manner, the Indexer makes it much easier to pull the rifle into your shoulder and maintain control while shooting.
Additionally, the wider, flatter profile of the Indexer functions very well as a hand stop or barricade stop, and also works as a forward limit to prevent your fingers from slipping off shorter handguards onto a hot barrel or suppressor. The Indexer is CNC machined from 6061-T6 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP25/T25 Torx wrench for installation (not included)."
(edit 5/25): $40.00 both (or $20.00 each).
Prefer face to face in Tigard at Oregon Rifle Works, Newberg at Highline gun shop, or in Estacada at Copeland Gunworks.
*I am willing to ship but please add $10.00 to get it via UPS insured.
Hope you can use it
Like New - this is great (M-LOK) equipment!
Hand Stop:
"The Arisaka Defense Hand Stop is a continuation of low profile, minimal control accessories. The primary goal of this accessory is to aid the user in pulling their rifle into their shoulder, enhancing control and recoil mitigation. The Hand Stop can also be used as a barricade stop, or reversed and placed at the front of the handguard to prevent the support hand from slipping off the end. The size and profile were designed to fit a wide variety of hands without being too large to get in the way. The Hand Stop is CNC machined from 6061-T6 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP20/T20 Torx wrench for installation (not included).
Height: 1.3"
Width: 0.625" at widest point.
Length: 1.4"."
Indexer:
"The Arisaka Defense Indexer is a continuation of the low profile, minimal control accessories Arisaka is known for. It was developed due to end-user demand for an M-Lok version of the Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. The Indexer can be used in a variety of ways, but the main intent is to place it between two fingers (usually index and middle). This typically places it further forward on the handguard, which also means it doesn't get in the way when transitioning to kneeling or prone shooting positions, where most people move their support hand towards the rear. Used in this manner, the Indexer makes it much easier to pull the rifle into your shoulder and maintain control while shooting.
Additionally, the wider, flatter profile of the Indexer functions very well as a hand stop or barricade stop, and also works as a forward limit to prevent your fingers from slipping off shorter handguards onto a hot barrel or suppressor. The Indexer is CNC machined from 6061-T6 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP25/T25 Torx wrench for installation (not included)."
(edit 5/25): $40.00 both (or $20.00 each).
Prefer face to face in Tigard at Oregon Rifle Works, Newberg at Highline gun shop, or in Estacada at Copeland Gunworks.
*I am willing to ship but please add $10.00 to get it via UPS insured.
Hope you can use it
Last Edited:
