Thread: thoughts about trust marking requirements?

i was thinking.

would a riveted or pinned identification plate affixed to the receiver of the firearm with trust name, city and state on it fulfil the identification requirements for marking?

this assumes correct etching depth, font, size, etc. for the text itself.

this would only require a couple of small holes to be drilled in the receiver to allow the rivets to pass through for attachment, but wouldn't permanently muck up the reciever itself.

something like this:

The answer is NO as it does not meet the marking requirements.

Unless of course the "identification plate" IS the NFA registered weapon.

Much like a silences has to be identified on the body, and not a removable part.

so, the 2 things that caught my eye were the 'placing' verbiage, and 'readily altered, obliterated, or removed' (emphasis added by me)

i would think that if you steel crush riveted (like ak builder rivets) a flat piece of steel with the lettering marked in a lawful size and depth, directly to the reciever (like any other part on a firearm.. that would satisfy the 'placing' and 'readily altered, obliterated, or removed' requirements rather perfectly.

think handgrip reinforcement plate, or side rail scope mount on an AK,

after all, like serial numbers or other factory markings, it would require the use of tools to remove the plate from the reciever, once riveted to the reciever. it would be essentially an ID plate, which, the identification of an NFA item, seems to be the idea of marking in the first place? you would have to drill or cut the rivet, which, seems to be the same or more effort than grinding off a serial number on a frame or what have you.

after all, a barrel extention is considered 'permantly affixed' as long as its blind pinned, right? thats even less material than a crush rivet.

[Code of Federal Regulations]
[Title 27, Volume 2]
[Revised as of April 1, 2003]
From the U.S. Government Printing Office via GPO Access
[CITE: 27CFR479.102]
[Page 188-189]
TITLE 27--ALCOHOL, TOBACCO PRODUCTS AND FIREARMS
CHAPTER II--BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES,
DEPARTMENT OF JUSTICE
PART 479--MACHINE GUNS, DESTRUCTIVE DEVICES, AND CERTAIN OTHER FIREARMS--Table of Contents
Subpart G--Registration and Identification of Firearms
Sec. 479.102 How must firearms be identified?
(a) You, as a manufacturer, importer, or maker of a firearm, must
legibly identify the firearm as follows:
(1) By engraving, casting, stamping (impressing), or otherwise
conspicuously placing or causing to be engraved, cast, stamped
(impressed) or placed on the frame or receiver thereof an individual
serial number. The serial number must be placed in a manner not
susceptible of being readily obliterated, altered, or removed, and must
not duplicate any serial number placed by you on any other firearm. For
firearms manufactured, imported, or made on and after January 30, 2002,
the engraving, casting, or stamping (impressing) of the serial number
must be to a minimum depth of .003 inch and in a print size no smaller
than 1/16 inch; and
(2) By engraving, casting, stamping (impressing), or otherwise
conspicuously placing or causing to be engraved, cast, stamped
(impressed), or placed on the frame, receiver, or barrel thereof certain
additional information. This information must be placed in a manner not
susceptible of being readily obliterated, altered or removed. For
firearms manufactured, imported, or made on and after January 30, 2002,
the engraving, casting, or stamping (impressing) of this information
must be to a minimum depth of .003 inch. The additional information
includes:
(i) The model, if such designation has been made;
(ii) The caliber or gauge;
(iii) Your name (or recognized abbreviation) and also, when
applicable, the name of the foreign manufacturer or maker;
(iv) In the case of a domestically made firearm, the city and State
(or recognized abbreviation thereof) where you as the manufacturer
maintain your place of business, or where you, as the maker, made the
firearm; and
[[Page 189]]
(v) In the case of an imported firearm, the name of the country in
which it was manufactured and the city and State (or recognized
abbreviation thereof) where you as the importer maintain your place of
business. For additional requirements relating to imported firearms, see
Customs regulations at 19 CFR part 134.
(b) The depth of all markings required by this section will be
measured from the flat surface of the metal and not the peaks or ridges.
The height of serial numbers required by paragraph (a)(1) of this
section will be measured as the distance between the latitudinal ends of
the character impression bottoms (bases).
(c) The Director may authorize other means of identification upon
receipt of a letter application from you, submitted in duplicate,
showing that such other identification is reasonable and will not hinder
the effective administration of this part.
(d) In the case of a destructive device, the Director may authorize
other means of identifying that weapon upon receipt of a letter
application from you, submitted in duplicate, showing that engraving,
casting, or stamping (impressing) such a weapon would be dangerous or
impracticable.
(e) A firearm frame or receiver that is not a component part of a
complete weapon at the time it is sold, shipped, or otherwise disposed
of by you must be identified as required by this section.
(f)(1) Any part defined as a machine gun, muffler, or silencer for
the purposes of this part that is not a component part of a complete
firearm at the time it is sold, shipped, or otherwise disposed of by you
must be identified as required by this section.
(2) The Director may authorize other means of identification of
parts defined as machine guns other than frames or receivers and parts
defined as mufflers or silencers upon receipt of a letter application
from you, submitted in duplicate, showing that such other identification
is reasonable and will not hinder the effective administration of this
part.

Originally Posted by jazz hand stumps

after all, a barrel extention is considered 'permantly affixed' as long as its blind pinned, right?

Not exactly...

http://www.atf.gov/publications/down...-chapter-2.pdf

The ATF procedure for measuring barrel length is to measure from the closed bolt (or breech-face) to the furthermost end of the barrel or permanently attached muzzle device. Permanent methods of attachment include full-fusion gas or electric steel-seam welding, high-temperature (1100°F) silver soldering, or blind pinning with the pin head welded over. Barrels are measured by inserting a dowel rod into the barrel until the rod stops against the bolt or breech-face. The rod is then marked at the furthermost end of the barrel or permanently attached muzzle device, withdrawn from the barrel, and measured.

I think the issue would be that a rivited plate is easy to move from one weapon to another. I could in theory move the plate every week to a new gun with minimal effort or blemish. Your not going to grind or fill the old reciever and engrave a new reciever every week.

How does glock work their serial number scheme in? It looks like a thin metal crush tag loop



The same thing, made new would be a loop of steel swaged through a couple of slots in the frame

glock: any variance to the CFR in respect to marking can be submitted to BATF for a ruling

I received my manufacturing FFL a couple of years ago, however I haven't found the 5 to 6 grand needed for an engraving machine yet...I hope you are on an affordable track to discover a cheaper way to satisfy the aft's engraving rules...

Originally Posted by billdeserthills

I received my manufacturing FFL a couple of years ago, however I haven't found the 5 to 6 grand needed for an engraving machine yet...I hope you are on an affordable track to discover a cheaper way to satisfy the aft's engraving rules...

A trip to the laser engraver is usually about $30

there are laser engravers....and there are LASER ENGRAVERS. the trick is to find
someone who has invested in a laser unit which will meet CFR requirement for depth.
it's relatively easy to find someone who can handle font size.

A 30 watt laser will do just fine especially on Aluminum. Swift tool in Kent has a 60 watt and they'll do work while you wait..

i'm going to open this can...

some guys don't engrave, and leave 4H blank.