Results 1 to 15 of 15

Thread: Is a one-size fits all can feasible?

  1. #1
    Senior Member
    Join Date
    Oct 2009
    Location
    Clark County
    Posts
    674

    Default Is a one-size fits all can feasible?

    I'm new to the suppressor world but here's what I want to suppress:

    Savage 110 FCP-K 300 WM
    Savage 10 FCP-K 223/5.56
    Savage Mark II FV 22LR

    The FCP-K's have Muzzle brakes and I believe they are threaded 5/8-24. The Mark II has a bull barrel and I would get it threaded to the same.

    I understand that if I got a suppressor that could work for the 300 WM it would probably be huge on the 22LR but other than the size issue and getting one that can be cleaned is there any reason why this wouldn't work?

    I may just get a .22 silencer for my Mark II and my Ruger Mark III pistol if the above isn't feasible but ideally it would be cool to only have to buy one suppressor.

  2. #2
    Senior Member
    Join Date
    Nov 2008
    Location
    Oregon
    Posts
    553

    Default

    I would personally get a .22can and then a 30cal can rated for your wing. That's a lot of pressure.

  3. #3
    Senior Member
    Join Date
    Oct 2009
    Location
    Clark County
    Posts
    674

    Default

    What do you mean by "a lot of pressure"?

    I want to use the .30 cal can on the .22 - I would think that there would be less pressure with the .22. But then again I don't know anything about silencers.

  4. #4
    Banned
    Join Date
    Aug 2008
    Location
    Beavertown OreGUN!
    Posts
    2,287

    Default

    Running .22 in a rifle can will lead it up...

    Not good.

    plus once you get one CAN you will want more , trust me

  5. #5
    Member
    Join Date
    Jun 2009
    Location
    PDXish
    Posts
    68

    Default

    You've got several issues that you're running up against.

    The first you've already touched on- size.

    The second issue is the leading that occurs in cans that have .22 lr run through them as a result of lead vapor deposition. When you shoot your 300WM over the top of that leading, you'll get exposed to a bunch of lead vapor because of the increased heat and pressure from the 300WM round- and your .223 for that matter, but I'd imagine it would be worse with the 300.

    Next is your desire for a can you can disassemble and clean (which I HIGHLY reccommend for a .22 suppressor!)- any of the cans that I know of for the high pressure centerfire cartridges cannot be taken apart because they would then not be structurally sound enough to handle the pressures.

    Finally, you'll run into a thread pitch issue if you ever want to use a standard .22 can on something you've threaded 5/8, although since 5/8 is a larger diameter than the 1/2x28 typically used for rimfire, you could concievably have your barrel rethreaded.

    From personal experience, I'll pass along some unsolicited advice that was given to me when I started getting into the NFA game- get yourself a separate .22 can. You'll probably end up shooting it more than all your others. They were right- I use my Sparrow more than all my other cans combined.

    BGRF

  6. #6
    Senior Member
    Join Date
    Oct 2009
    Location
    Clark County
    Posts
    674

    Default

    Thanks for the advice. I guess I'll start with a .22 can as I do think it will get used the most use. It still would be cool if there was a .30 cal can that could be cleaned.

  7. #7
    Senior Member
    Join Date
    Dec 2010
    Location
    Yakima and N of Spokane
    Posts
    1,519

    Default

    As stated at the least get a take apart .22 can and another of your choice. I wanted a .223 can for a long time but I bought a .30 cal can first. With the .30 cal you can shoot anything under .30 cal though it. I run my .30 cal on my target AR the most and it is awesome.

    I currently own 3, .22 cal cans, 2 9mm cans, 1, .30 cal can. I am going to be building or buying a .45 sometime this year.

    All of mine get quite a bit of use and they are a ton of fun. As it was stated it become addicting.

  8. #8
    Senior Member
    Join Date
    Dec 2008
    Location
    Hillsboro
    Posts
    1,170

    Default

    Tom bowers at subgun.org makes quality and different thread pitches that you can use for each different firearm.

  9. #9
    Senior Member
    Join Date
    Jan 2009
    Location
    Oregon
    Posts
    360

    Default

    Quote Originally Posted by Nwcid View Post
    As it was stated it become addicting.
    Amen to that. I've got four stamps with five and six pending.

  10. #10
    Senior Member
    Join Date
    Oct 2009
    Location
    Clark County
    Posts
    674

    Default

    I did find this suppressor:

    Liberty Suppressors - The Constitution 5.7x28mm Rifle Silencer

    The Constitution is elegant simplicity in design, intuitive of maintain, full auto rated, take
    apart, monolithic core, and made entirely of alloy steel. This suppressor was designed
    for the person wanting to have a suppressor that could be used on their FN PS90SBR
    that could also work on his or her 223 caliber AR15 and then switched over to their 22LR
    AR upper without having to buy 2 suppressors due to the lead buildup issues of the
    22LR. We have had a large number of requests for suppressors with these features. This
    suppressor is intended for use on carbines and not handguns, although it will work fine
    on a handgun, there are 22LR suppressors intended for handgun use that are much
    lighter.... (Kodiak and Kodiak TL).
    It is kind of tempting to go with this and then I can suppress everything but my 300 WM. I've got some other .22's and an AR that could probably do with some suppression.

  11. #11
    Senior Member
    Join Date
    Dec 2010
    Location
    Yakima and N of Spokane
    Posts
    1,519

    Default

    The only problem I see with "one size fits all" cans is that they are not usually quite that.

    A can that is big enough to handle .223 is going to be large and heavy on most .22 guns. The have linked is 24 oz My .30 cal can is 26 oz. and it is very heavy on the end of a rifle. My 9mm Trident can is only 9 oz and my Outback 2 cans (both mod to take down) are 2.5 oz or 10x lighter then the one you link.

    I know you are using it on all rifles so far but most .22 pistols would weigh less then that can and the sights would be covered from the large diameter.

    I know on my .300 Whisper AR the difference between the 9 oz Trident and the 26 oz .30 cal is huge. With the .30 cal it is very nose heavy, with the Trident it is hardly noticeable.

    Just something to think about.

  12. #12
    Senior Member
    Join Date
    Feb 2010
    Location
    206
    Posts
    592

    Default

    Im in somewhat the same boat but looking at a 7.62 for my AK and AR in 5.56. YM makes a setup that has a threaded compensator that interfaces with their 8" can that they have available for 600 ish.

    Looking into it.

  13. #13
    Senior Member
    Join Date
    Oct 2009
    Location
    Clark County
    Posts
    674

    Default

    Thanks for the heads up on the weight issue. I noticed that Liberty also has a 13oz 9mm take apart can that they claim can be used with 22LR and .223 (at a low rate of fire).

    Liberty Suppressors Mystic 9mm Multipurpose Suppressor

    Mystic Multipurpose Suppressor
    MSRP: 750$

    Weight of suppressor: 13 Ounces

    Length/Diameter : 8” x 1.375”

    Material: Stainless steel / Titanium

    Attachment: Multiple styles

    Approx. DB Reduction: 38dB (This is with Fiocchi 158 gr 9mm
    which was showing 162dB unsuppressed)

    Calibers : 9mm, 22LR, 300/221, 300BLK, 357 MAG, 338 Spectre

    There has been a lot of interest in using this unit on 223 rifles as well as the intended caliber. It can be used on 223
    under limited conditions. Low rates of fire with cooling periods and no mirage covers. The use of a mirage cover
    will hide the obvious indicator of the unit getting hot by producing mirage. This is a great indicator to let the
    shooter know that the can needs to cool off. Also, in 223 the barrel must be at least 16" in length.

    Available in one of four configurations:
    1. No mount - you have the mounts you need already
    2. Recoil booster for pistol use with suppressor
    3. Fixed barrel mount for carbine use with suppressor
    4. Adapter ring for Triad mount with suppressor

    All of our mounts will also be available individually as well.
    Looks like I could even use this with my Glocks.

    I'm not trying to be a smart *** (but it probably seems that way) - but I don't see myself being that heavy of a suppressor user (although that may change). I just want to get one for the fun and if it works on a couple different guns that would make it "funner".

    I do appreciate all the points and advice.

  14. #14
    Senior Member
    Join Date
    Dec 2010
    Location
    Yakima and N of Spokane
    Posts
    1,519

    Default

    Quote Originally Posted by PBinWA View Post

    I'm not trying to be a smart *** (but it probably seems that way) - but I don't see myself being that heavy of a suppressor user (although that may change). I just want to get one for the fun and if it works on a couple different guns that would make it "funner".

    I do appreciate all the points and advice.
    Not smart *** at all. Got to ask to know, and search for as much info as you can.

    I think you will shoot with your can more then you think. I easily do 99% of with silencers on the guns that are fitted to be shot with them. More then 75% of my shooting is done with my guns that are set up for my silencers.

    One other thing I will say in the world of cans is get what you want the first time. With guns you can buy and sell and trade loosing little value. Cans are next to worthless once you buy them. Take a $500 can, add $200 tax and say $100 worth of fee's/shipping/fingerprints/passport photos/ect. Now you have spent $800. Since the can is now used you are going to have to knock at least $100 off to sell it. So now you literally own something you paid $800 for that at max is worth $400. If you sell out of state there is a second $200 transfer fee making the silencer worth $200 tops. I love my cans but learn what you want and buy what you want the first time. It may cost a little more up front but in the long run will be much cheeper.

  15. #15
    Senior Member
    Join Date
    Jan 2009
    Location
    Oregon
    Posts
    360

    Default

    Quote Originally Posted by Nwcid View Post
    I think you will shoot with your can more then you think. I easily do 99% of with silencers on the guns that are fitted to be shot with them. More then 75% of my shooting is done with my guns that are set up for my silencers.
    After you start shooting with a silencer you'll find you won't like shooting without them. The only time I shoot without is if someone wants to hear the difference, then it quickly goes back on.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •